|
|
|
| DIY & SAVE $ - BYPASS TIP - EBOOK - VIDEO - TUB LIGHT |
| Category:
Major Appliances
/
Washers & Dryers
/
Parts & Accessories
|
 |
| Start Price: |
USD 29.97 |
Click Here
to See More
|
| Current Price: |
USD 34.97 |
| Reserve Price: |
- |
| Time Left: |
- |
| Bid Count: |
1 |
| Buy It Now Price: |
USD 34.97 |
| Start Time: |
11/20/2008 |
| End Time: |
11/22/2008 |
| Location: |
Grove City, Ohio |
|
Problem: Your Neptune front loader washer won't spin and the door lock locked light doesn't come on anymore and your spouse is unhappy because the laundry is pilling up really FAST! Solution: My Deluxe Maytag Neptune washer R11 Q6 repair kit with new wax motor! Ø 100% Money Back Guarantee if your not satisfied Ø Courtesy call to walk you through the repair and answer any questions Ø Includes link to my 6 minute video which shows you how to replace R11 and Q6 Ø Ebay PowerSeller Ø I can create an Ebay listing for any Neptune part you need Ø 1770+ feedbacks This Deluxe Neptune repair kit includes: · My latest Neptune E-book which includes my personal email and PHONE NUMBER to call for PHONE TECHNICAL SUPPORT, bonus links to My R11/Q6 Video, link to 150 page PDF service manual, disassembly guide, soldering how-to information, Neptune information, tips and much more! · New genuine Maytag 12002535 wax motor (black actuator pin) · Replacement for R11 · Replacement for Q6 (600 Volt / 1 Amp) · Replacement 10 Watt tub light · Courtesy call from me! · 3†piece of solder wick (for removing old solder) · 3†piece of circuit board repair wire · 6†piece of solder This Repair kit is for the 2000 Stacker, MAH3000, MAH4000 and MAH5500A (not MAH5500B’s) Neptunes. Unplug Machine a.s.a.p. Don't turn Neptune ON before removing the upper control board and cutting Q6 (make sure cut leads can't touch!) and R11 out to prevent any more damage. Try machine to see if the water will fill. If no water, your board suffered more damage than usual and you will have to replace control board which I can list for you on Ebay. Send me an email via Ebay's contact seller link. To Bypass Spin enable switch (only after you removed Q6 and R11) while you wait for your repair kit simply jamb some cardboard in the right microswitch (red & yellow wires) in the door latch assembly to keep switch fully pressed in. Keep in mind that the Neptune will not stop at the end of cycle when bypassed and will need to be turned off manually. Some soldering is required to replace R11 and Q6. If you can’t solder find someone who can… and save some money. You are going to need a new circuit board anyway unless you can repair it yourself so what do you have to lose? You can take control board and repair kit to a television repair center and they can replace R11/Q6 for you. Purchasers need a working email account, as my latest report will be sent to you electronically to the email that is on record at Paypal. The remaining repair kit will be sent via how you select. Please add your phone number in the notes section when checking out with Paypal to get your courtesy call. I also provide the Neptune bearing & seal kit for those Neptunes that sound like a jet taking off in high speed spin cycle. This way you don't have to replace the outer tub which now runs $500 or so. Check out my other items for more information. Following is the Neptune teardown procedure: (note: place mouse over picture to read text) T Now it's time to tackle the upper control board... Simply reverse these teardown procedures after you change out the wax motor and operate on the control board. Below is the upper control board before and after R11 and Q6 was replaced and the back side. Notice how the R11 leads were used to connect to the next available connection because of copper track damage? Check out my other items! Thank you for looking and I look forward to serving you!
Place a Bid!
|
HOME
|
|